Damchex SX
| Appearance | Amber, viscous liquid |
| Odor | Petroleum |
| Density [25°C] [77°F] | 7.78 lbs / gal |
| Viscosity [25°C] [77°F] | 1500 to 3500 |
| Flash Point TCC | 182°C (360°F) minimum |
| Sulfur | >10% |
| Storage life |
At least 12 months in a sealed container at room temperature |
- Description
- Advantages
- Recommendations for use
Damchex SX is an anti-checking compound to be used on finish molds and blanks. It is sulfurized polymer without graphite. It was designed to enhance the thermal stability, to improve the cleanness, to prolong the service life, and to reduce sulfur odor of the product.
After being appropriately swabbed, Damchex SX will be dried quickly forming a uniform lubricant film. An appropriate swabbing approach should be adjusted and found by operators depending upon a real application situation.
After being appropriately swabbed, Damchex SX will be dried quickly forming a uniform lubricant film. An appropriate swabbing approach should be adjusted and found by operators depending upon a real application situation.
NON-GRAPHITED, TOUCH-UP COMPOUND
PROVIDES RELEASE AND BURNS OFF CLEANLY
EXCELLENT INSULATION CHARACTERISTICS
SUPERIOR ANTI-CHECKING PROPERTIES
IMPROVES EFFICIENCY OF THE FORMING OPERATION
COATING GRADUALLY DECOMPOSES & VANISHES
PROVIDES RELEASE AND BURNS OFF CLEANLY
EXCELLENT INSULATION CHARACTERISTICS
SUPERIOR ANTI-CHECKING PROPERTIES
IMPROVES EFFICIENCY OF THE FORMING OPERATION
COATING GRADUALLY DECOMPOSES & VANISHES
SWAB PREPARATION
Presoak swabs in mineral oil
Presoak enough swabs for 1 shift
This improves the efficiency of swabbing
LOAD SWAB IMMEDIATELY AFTER LUBRICATING CYCLE
Reload swab directly after swabbing while the swab is still hot
A hot swab makes it easier for Damchex SX to efficiently penetrate into the center of the swab.
ALWAYS HANG SWABS UP AFTER USE
This practice avoids swab laying in the dope tray and getting saturated with oil
Helps keep swabs properly loaded with lubricant
ON THE MOLD SIDE
Lubricate the top of the mold so there will be no mold checks underneath the finish
Lubricate the seams of the mold so there will not be any seam checks
Lubricate by rubbing the engravings of the blow mold
Lubricate around the bottom plate and mold match to eliminate heel checks
ON THE BLANK SIDE
Lubricate the baffles - top lips of the blank and shoulder areas
Lubricate areas of the blank which correspond to defects on the bottle
IN PRESS OPERATIONS
Lubricate around the plunger
Lubricate the joints of the mold
Lubricate the ring seat of the mold
Lubricate between the plunger and the ring
Presoak swabs in mineral oil
Presoak enough swabs for 1 shift
This improves the efficiency of swabbing
LOAD SWAB IMMEDIATELY AFTER LUBRICATING CYCLE
Reload swab directly after swabbing while the swab is still hot
A hot swab makes it easier for Damchex SX to efficiently penetrate into the center of the swab.
ALWAYS HANG SWABS UP AFTER USE
This practice avoids swab laying in the dope tray and getting saturated with oil
Helps keep swabs properly loaded with lubricant
ON THE MOLD SIDE
Lubricate the top of the mold so there will be no mold checks underneath the finish
Lubricate the seams of the mold so there will not be any seam checks
Lubricate by rubbing the engravings of the blow mold
Lubricate around the bottom plate and mold match to eliminate heel checks
ON THE BLANK SIDE
Lubricate the baffles - top lips of the blank and shoulder areas
Lubricate areas of the blank which correspond to defects on the bottle
IN PRESS OPERATIONS
Lubricate around the plunger
Lubricate the joints of the mold
Lubricate the ring seat of the mold
Lubricate between the plunger and the ring
